PipeForgev2.1 Threaded Take-Off Pro

Quick Take-Off Calculator

Threaded NPT
The dimension you measured (or want).
Optional — shown on saved calcs.

Result & Diagram

C-C
Pipe Cut Length
— inches
—
Resulting Assembly
—
A Throw —
Take-off A —
B Throw —
Take-off B —
Thread Makeup —
enter a measurement to see the math

Multi-Segment Run

Up to 6 segments

How It Works

Build a continuous threaded run as a chain of up to 6 segments. Each segment has its own left fitting, mode, measurement, and right fitting. Per-segment cut lengths sum to a grand total for ordering pipe.

Total Pipe Length Required
— in
Segments
0
REFERENCE VALUES ONLY. Dimensions are ASME B16.3 Class 150 malleable iron threaded fittings, sourced from manufacturer catalog tables (CCTF) which conform to the standard. Gate valve dimensions are representative; valves are manufacturer-specific. Always verify against the actual product data sheet before fabrication. Not for engineered submittals.

Fitting Dimensions (in)

ASME B16.3
Size 90° (C-E) 45° (C-E) Street 90° (C-E) Street 45° (C-E) Tee (C-E) Cross (C-E) Coupling (OAL) Union (OAL) Cap (H) Gate Valve*

* Gate valve OAL is representative; varies by manufacturer.

NPT Thread Engagement

ASME B1.20.1

Trade Vocabulary

L1 — Hand-tight engagement. The distance the threads engage when the pipe is screwed in by hand to a snug stop. Used by the B1.20.1 L1 thread gage to inspect threads.

L3 — Wrench make-up. The additional engagement beyond hand-tight, achieved with a pipe wrench to make a seal.

Effective Makeup (used in this calculator) = L1 + L3. This is the distance the pipe disappears into the fitting at full wrench-tight assembly. Edit per-shop in Thread Settings.

Throw = the C-E (center-to-end) dimension of a fitting. Take-off = throw − makeup.

SizeTPIL1 (hand)L3 (wrench)L1+L3Active Makeup *

* Shop override active where shown.

Shop Standards — Fitting Dimensions

Editable · saved on device

Override Dimensions Per Shop

Edit any cell to override the ASME default with your shop's measured value. Changes save automatically to this device. Use Reset to Defaults to restore ASME B16.3 nominal values.

Size 90° 45° Street 90° Street 45° Tee Cross Coupling Union Cap Gate Valve*

Custom Fittings

Define your own

Add a Custom Fitting

For non-standard fittings — dielectric unions, hammer unions, specialty valves, anything not in the ASME catalog. Custom fittings appear in dropdowns when the size matches.

Geometry types: center = like an elbow/tee (uses throw + makeup), inline = like a coupling (uses OAL/2), terminator = like a cap, end = no take-off.

NameSizeTypeDimAction

Thread Makeup — Per Size

ASME B1.20.1 · editable

What This Controls

The "thread makeup" is how far the pipe enters the fitting after wrench tighten-up. Take-off = Throw − Makeup. The default is L1 + L3 from ASME B1.20.1 (full wrench-tight engagement).

Different shops, sealants, and tools land at slightly different makeups. Edit any row to match yours — for example, for 1″ pipe, dialing makeup to 0.625″ gives the 7/8″ take-off many shops use on 1″ 90° ells.

SizeTPIL1 handL3 wrenchL1+L3 defaultShop override (in)

Measurement Guide

Pick the right mode
FIELD TIP: Always confirm which two points you measured between — the math depends on it. When in doubt, measure twice and use the simpler mode (E-E or C-C).

Center-to-Center (C-C)

Cut = Field − TA − TB

Two fittings, measured between their centerlines. Subtract the effective take-off on both sides. Most common between two elbows or tees.

Center-to-End (C-E)

Cut = Field − Tfitting

One side has a fitting, the other is a bare pipe end. The measurement spans from the fitting's center to the bare end. C-E and E-C are the same measurement — it doesn't matter which side you call "first." Just put the fitting on whichever side it physically is.

Bryan's example: 48″ from a bare pipe end to the center of a 1″ 90° elbow. Take-off = 1.50 − 0.68 = 0.82″. Cut = 48 − 0.82 = 47.18″ (≈ 47 3/16″).

End-to-End (E-E)

Cut = Field

Both ends bare pipe. No take-off to subtract — cut equals what you measured. Useful for swaging, grooving, or pre-cutting nipples.

Face-to-Face (F-F)

Cut = Field + 2 × Makeup

You measured between the visible faces of two fittings. The pipe must extend past each face into the fitting by the makeup amount, so we add two makeups.

The "End" Fitting

T = 0

"End" represents a bare pipe end. Selecting it on a side forces that side's take-off to zero. The calc will warn if your mode/fitting pair doesn't make sense.

Trade Vocabulary

Know the words

Throw

The center-to-end dimension of a fitting — how far the centerline reaches outward from where the pipe enters. For a 1″ 90° elbow, throw = 1.50″.

Thread Engagement / Makeup

How far the pipe screws into the fitting at full wrench-tight. Per ASME B1.20.1: L1 (hand-tight) + L3 (wrench make-up). For 1″ NPT ≈ 0.68″.

Take-off

The piece of the fitting that replaces pipe in the final assembly. Take-off = Throw − Makeup. For 1″ 90°: 1.50 − 0.68 = 0.82″. Many shops use 7/8″.

Cut Length

What you actually cut the pipe to. Comes from the assembly dimension you want, minus the take-off on each fitted end.

Assembly / Finished Length

The end-to-end (or center-to-center, depending on mode) dimension of the installed pipe + fittings.

Nipple

A short threaded length of pipe. Calculator will warn if a cut comes out under 1.5″ — that's close-nipple territory and may need a pre-fab.

Worked Example — Bryan's 48″ C-E

You want a finished dimension of 48″ from a bare pipe end to the center of a 1″ 90° elbow. (Some shops call this "end-to-center" — same thing. Use mode C-E and put the elbow on whichever side it physically is, with "End" on the other.)

1″ 90° throw (C-E) = 1.50″. Thread makeup (L1+L3) ≈ 0.68″.

Take-off = 1.50 − 0.68 = 0.82″. Cut = 48 − 0.82 = 47.18″ (≈ 47 3/16″).

If your shop standard uses 7/8″ take-off (makeup = 0.625″), cut = 48 − 0.875 = 47.125″ (47 1/8″). Tune in Thread Settings.

Saved Calculations

0 / 30

Stored On This Device

The 30 most recent saved calcs are kept locally. Tap Load to reopen any calc in Quick Calc. Tap Delete to remove a single calc.

No saved calcs yet. Use Save Calc on the Quick Calc tab.